HOW DID IT ALL BEGIN?
In the late part of the 1980’s, the inventor worked with reflective coating companies that claimed they made “NASA ceramic paints.” During the time that he worked with the reflective companies he learned that the formulas used for reflective paints were actually not made from NASA technology and were only good for light reflection. When the coatings became dirty or tarnished the coatings did not actually reflect heat.
In 1987-88, the inventor made contact with NASA directly to ask the ceramic engineers what kind of ceramics to use to make an insulation coating. The ceramic engineers at the Marshall Space Center told the inventor that they had never developed a ceramic insulation paint and that the marketing materials used by the reflective companies that claimed they used “NASA Technology” were not true. The inventor then asked the engineers what types of ceramics they would recommend to use in a coating that could provide insulation. The engineers worked with the inventor for some time to choose which ceramics out of the engineering books would be most successful in blocking heat. The inventor tested all the ceramics suggested by the NASA engineers and found that none of the suggested ceramics were successful in blocking heat.
After the unsuccessful testing, the NASA engineers helped the inventor by directing him to ceramic suppliers around the world so that he could make contact with them to obtain ceramic samples. Thus began a long Research and Development period primarily using the trial and error method; testing each individual ceramic compound to see if it could block and repel heat when placed in a coating. From this development process, which occurred between 1988-1992, a true Ceramic Coating was developed using three ceramic compounds which would meet the needs of heavy industrial plants and petrochemical areas for insulation of pipes, tanks and facilities.
The first Ceramic Coating formula was sold to industrial users in 1989. By 1992 the inventor had tested over 700 compounds in determining which ceramic compounds would be most effective in blocking heat waves. The important point of this testing was to find ever more effective ceramic compounds that could continue to block heat waves even after the coating became dirty and less white in colour.
In this process of discovery the R & D process showed that density, crystalline structure and size were the most important characteristics that made the ceramic compound work. It was found that low density compounds would not absorb heat. The density of the chosen ceramics was so low that heat could not be absorbed into the compound. By way of an example, it is easy for dense metal to absorb heat and become hot while less dense paper cannot absorb heat and will not become hot. The ceramic compounds that are used are 50 times less dense than paper and, therefore, heat cannot load or absorb into them.
Crystalline structure is the design of the ceramic compound. This becomes important when the structure is made to repel heat movement over the compound and to throw off the heat from the surface. The size is very important to be able to block the radiation wave as it hits the coating surface.
In testing performed by engineers in Germany, a study was made to determine what materials and size would be most effective in blocking the heat waves of infrared long wave radiation and visual light or short wave radiation from entering or passing through a coating. Infrared radiation was known to represent 57% of the heat from radiation, 40% was from visual light (light spectrum) and 3% of the heat load is from ultra violet (UV) radiation, which is not significant. The Ceramic Coating tested was found to block 99.5% of long wave radiation and 92% of short wave radiation. The ceramic compounds also naturally blocked the UV. To successfully block heat waves and heat buildup on a surface, the chosen ceramic compounds perform the function of blocking the heat waves from passing through the coating into the building and other ceramic compounds will block the heat that would norm ally build up on the surface that would then conduct to the interior.
From 1992-2012 an additional 2900+ compounds (total of 3600) were tested to find compounds that could improve the existing Ceramic Coatings or develop new insulation or high heat coatings that would provide answers to insulation problems in industrial environments. In many areas of industrial complexes fiberglass or rock wool cannot work well and concrete mixtures are not a good solution. As an alternative, the high temperature Ceramic Coating can be sprayed into place in few man-hours, is easy to apply, is safe for workers and the environment and is extremely effective.
A tremendous amount of research and testing was performed over a 22-year period to determine the best selection of ceramic compounds to provide a total insulation program. From the initial research used to develop the heat radiation blocking Ceramic Coating, additional research has found new ceramic compounds and combinations of these compounds to formulate other coatings that could be used to insulate high heat environments such as hot pipes, furnace walls and ceilings, provide fire control of structural steel, insulate apartments, housing and industrial areas and to protect all building materials used in construction.
It was determined early on that R&D testing was the only way to fully understand a compound and how it could or would act when mixed into a resin system with water and other raw materials. There are no books written with a study of ceramic compounds and how each functions, or fails, in all circumstances or what happens when they are mixed into a formula. Therefore, R&D testing continues as a daily, weekly, monthly and yearly process investigating any and all new compounds brought to our attention. The search is on-going and will continue as we look for the next major breakthrough in heat control.
WHAT MAKES THESE COATINGS SO UNIQUE?
Comparing the Ceramic Coating to all the traditional thickness based insulation materials, which are designed to absorb and slow down the conduction of heat, is totally old fashioned and the consideration of what can provide the best insulation system is now due.
Traditional insulation materials have always been thickness based materials. The reason is simple: the heat loads onto the surface of the insulation and then conducts through the material. The material had to be thick in order to provide resistance and increase the time it takes for the heat to transfer or conduct through the material to the other side. This conduction method of insulation is gauged by the “R” or “K” values, which are simple measurements of the time it takes for heat to be absorbed and transfer through the material. As such, R and K are measures of the rate of heat transfer through the insulating material and have nothing to do with blocking or rejecting heat transfer.
All the marketing, all the education in the universities, all the principles of insulation were based upon increasing material thickness to buy as much time as possible from initial heat load to transfer through the material into the underlying substrate.
Traditional thickness based insulation materials were designed to address only conduction, and actually ignore radiation, which is the most dominant heat transfer mode under the sun. As such, all these traditional thickness based materials are designed only to slow down conduction. Fiberglass, rock wool, foam and other like materials accept most of the heat load on their surface and eventually allow the transfer of that heat load into the surface they are trying to protect. All these materials are based on “after-the-fact” management of heat load and are doing nothing more than trying to slow the transfer of 100% of the heat load.
Now consider Ceramic Coating. It is not thick and, therefore, how could it be effective in conductive resistance? The Ceramic Coating works to block the radiation causing the heat load. By blocking 95% of the initial heat load, there is only 5% of heat available for transfer, proving that the Ceramic Coating is more effective without the conventional standards of thickness. In addition, the Ceramic Coating provides a barrier against water (Federal Specification) and air movement. It has been studied and proven that a large percentage of heat loss or gain in the substrate is due to moisture load as well as air leakage, which causes the heat to quickly load and travel through the structure. The Ceramic Coating seals the substrate and blocks moisture load and air leakage, eliminating this type of heat transfer.
If only a 5% of the available heat loads onto a surface that is the target of insulation that is all that is available to enter into the substrate. Traditional thick insulation materials allow transfer of almost 100% of this heat load into the substrate because they are not designed to block the heat load. They are designed to absorb heat and slowly allow it to transfer, which transfer rate is what the “R” or “K” values measure.
Radiation is not the only heat transfer mechanism that the Ceramic Coating blocks. The Ceramic Coating blocks conduction as well. Blocking heat load is the key to measuring the effectiveness of the Ceramic Coating. If you block heat load you control the amount of heat gain into a structure.
While the concept of repelling or reflecting heat gain on the exterior of a structure is clear, the principle is the same for the interior. The Ceramic Coating’s ceramic blend resists the heat load because the ceramic compounds do not have the density to absorb and hold heat. What heat is absorbed into the coating is thrown back out of the coating to stabilize the heat and helps the convective heat movement between warm and cold areas stabilize quicker. This is called EMISSIVITY, which is a test measurement of how much or fast a surface can unload the heat it does absorb. Emissivity is a property of a material, not a rate of heat transfer. When an interior wall or ceiling is covered with the Ceramic Coating the relevant emissivity is that of the coating and not the underlying substrate material. In such case, the Ceramic Coating’s emissivity of 0.91 is throwing heat off its surface back to the room. Another interesting characteristic of the Ceramic Coating is that it actually works to control two recognized heat transfer modes – radiation, and conduction. Since it resists heat load and has a high emissivity, the Ceramic Coating assists the convection process to balance the interior room temperatures. NOTE: Convection inside a building moves heat from one location (hot area) to another location (cold area). It works to make the room temperature uniform. The surface properties have little to do with the heat transfer across the wall, i.e. from inside to outside. There is heat load into the wall, then conduction is the mode of transfer to the cool side.
The question then becomes, do you want to require more and more thickness to overcome the rate of heat transfer and then increase this thickness factor yet again to compensate for loss of effectiveness due to absorption of moisture (humidity) and air flow –or– would you rather block the initial HEAT LOAD and stop this process from ever occurring while blocking moisture and reducing air flow? This is the difference between using the Ceramic Coating and traditional thickness based materials.
Additionally, the Ceramic Coating’s properties are much more than just a heat control system blocking summer heat gain or winter heat lost. It is a complete coating system that provides a moisture barrier, a proven water barrier against a 60 mph wind driven rain, a sound barrier blocking up to 50% of voice frequency sound transmission through walls (due to the same ceramic properties that cannot load heat), a “0” fire spread Class A rating and a mould/mildew blocker. The Ceramic Coating system also helps to stop condensation while being able to breathe to avoid mould development. Traditional thickness based insulation materials have none of these properties.
In addition to the loss of effectiveness due to moisture absorption and air flow, another weakness of traditional thickness based materials is their loss of effectiveness when compressed. When traditional materials are installed between studs and joists they leave the studs and framing exposed to load and transfer heat. Further, when traditional fibrous materials are pushed and compacted into place their “R” values are reduced dramatically. A material rated to be a R19 at 6 inches is often forced into a standard stud wall where the stud is only 3 5/8″ deep, making the traditional insulating material an average of 3″ thick. Since the traditional material’s effectiveness is purely based on thickness, its R value would be reduced to R9.5 and it will never provide the advertised R19. Since most homes in the US and abroad use standard 2X4 stud construction, basing insulation on R value is completely subjective and once out of the lab and in the field cannot perform to its marketed performance. None of these problems occur when using a Ceramic Coating system. Conclusion: Traditional insulating concepts have not been updated in years and the tested and proven new ceramic based technology available today yields significant benefits and advantages over the old outdated concepts.

